Muster für USC-I2C und LM75
09.09.2012, 22:04
Hallo!
Status:
Treiber installiert.
Displaymodul über eine I2C Buchse angeschlossen. Jumper auf 2.
Testtool gestartet.
=> Dispay veränderbar. Taste und LED wollen nicht. ersteinmal egal.
LM 75 Anschluss Freihandverdrahtung: Top View:
Pin 1 = SDL (grün)
Pin 2 = SCL (gelb)
Pin 4 = GND (blau)
Pin 5,6,7,8 = Vdd (rot) Addresse 7
Testtool: Direkteingabe
"S90 01 00 P"
"S90 00 R 02 P"
=> nichts antwortet.
Ich habe auch andere Addressen nach
Address Byte
Immediately following the Start Condition, the host must
next transmit the address byte to the LM75. The four most
significant bits of the Address Byte (A6, A5, A4, A3) are
fixed to 1001(B). The states of A2, A1 and A0 in the serial
bit stream must match the states of the A2, A1 and A0
address inputs for the LM75 to respond with an
Acknowledge (indicating the LM75 is on the bus and ready
to accept data). The eighth bit in the Address Byte is a
Read–Write Bit. This bit is a 1 for a read operation or 0 for
a write operation.
ausprobiert. . . . . .
Wahrscheinlich bin ich mal wieder zu plöt die Beschreibungen richtig zu lesen, oder ich habe die falschen gelesen, oder es gibt Varianten des LM 75, oder oder oder.
Also schreibe ich euch, in um wenigstens eine Falsche Bedienung sicherzustellen.
Könnt Ihr mir schreiben wie die Richtige Addresse lautet?
Danke im voraus
Carsten
Status:
Treiber installiert.
Displaymodul über eine I2C Buchse angeschlossen. Jumper auf 2.
Testtool gestartet.
=> Dispay veränderbar. Taste und LED wollen nicht. ersteinmal egal.
LM 75 Anschluss Freihandverdrahtung: Top View:
Pin 1 = SDL (grün)
Pin 2 = SCL (gelb)
Pin 4 = GND (blau)
Pin 5,6,7,8 = Vdd (rot) Addresse 7
Testtool: Direkteingabe
"S90 01 00 P"
"S90 00 R 02 P"
=> nichts antwortet.
Ich habe auch andere Addressen nach
Address Byte
Immediately following the Start Condition, the host must
next transmit the address byte to the LM75. The four most
significant bits of the Address Byte (A6, A5, A4, A3) are
fixed to 1001(B). The states of A2, A1 and A0 in the serial
bit stream must match the states of the A2, A1 and A0
address inputs for the LM75 to respond with an
Acknowledge (indicating the LM75 is on the bus and ready
to accept data). The eighth bit in the Address Byte is a
Read–Write Bit. This bit is a 1 for a read operation or 0 for
a write operation.
ausprobiert. . . . . .
Wahrscheinlich bin ich mal wieder zu plöt die Beschreibungen richtig zu lesen, oder ich habe die falschen gelesen, oder es gibt Varianten des LM 75, oder oder oder.
Also schreibe ich euch, in um wenigstens eine Falsche Bedienung sicherzustellen.
Könnt Ihr mir schreiben wie die Richtige Addresse lautet?
Danke im voraus
Carsten